Serving Brooklyn, Queens and Long Island(929) 429-2429Open six days a weekFree estimateGuaranteed work
On Point Garage Doors
Open 24 hours Sun-Thu, Fri until 5 pm Free estimate Springs, openers, cables We come to you
Emergency?Call nowBook free estimate
New York, NY - open six days a week

Garage doors for auto repair shops and service bays

Free estimateSame-day serviceCommon parts on board
  • Free estimate
  • Same-day service
  • Common parts on board
Emergency garage door repair★★★★★ 5.0 on Google · 42 reviews

Book your free estimate

Takes 30 seconds. We call you back to set a time.

Or just call (929) 429-2429 and talk it through.

Home › Auto Shop Garage Doors

In an auto repair shop, the bay doors are part of the work. They open when a car comes in, close to hold heat while the work is done, and open again when the car goes out. A busy shop can cycle a door more in a week than a house does in a year. When a bay door fails, a lift sits empty and cars wait outside. This page explains which doors hold up in service bays, what wears out first and what we check on a shop visit. Free estimate at (929) 429-2429.

By Sean Cohen, owner, On Point Garage Doors · Updated

Real jobs. Real photos.

These photos are from our own jobs, with our logo on them.

Rolling steel doors in a commercial building, an On Point Garage Doors job
Commercial door on a city street
Steel door on a work building, from one of our jobs
Steel door on a work building
Roll-up door at a work entrance, from one of our jobs
Roll-up door at a work entrance

Doors that suit a service bay

  1. Insulated sectional doorsThe most common choice for shops that heat their bays. Sections with windows let mechanics see who is pulling in.
  2. Rolling steel doorsStrong and compact, coiling above the opening so the ceiling stays clear for lifts.
  3. Full-view glass doorsPopular on shops that want customers to see inside, with aluminum frames and glass or polycarbonate panels.

Ceiling space and lifts

A car lift raises the car toward the ceiling, and a sectional door's tracks run along the same space. In many shops the tracks are set to run higher up the wall, or a rolling door is used, so a raised car never meets an open door. Planning the lift and the door together saves trouble later.

Springs built for heavy use

Springs wear by cycles, not by years. A spring meant for a house can wear out quickly on a shop door. For a busy bay, we fit springs rated for many more cycles so they last far longer between changes. On a door that never rests, the heavier spring is the one that saves calls later.

Openers and controls

Shop doors usually run on commercial operators with a push button station by each bay, sometimes with a remote for the owner. Many shops add a timer to close doors left open, or a control that lets a single button run several doors. A commercial operator is built to run all day without overheating.

Safety around cars and people

Cars move under the door, and so do mechanics, customers and parts carts. Photo eyes at the bottom and a sensing edge on the bottom bar stop and reverse the door when something is in the way. These devices take a beating in a shop and should be checked whenever the door is serviced.

What wears out first

Heat, fumes and ventilation

Shops need fresh air while engines run, and heat in the winter. Many owners open one door partway for air, which is hard on some openers. A well balanced door with good seals keeps heat in when closed, and a door that stops cleanly at a partial height lets air move without straining the operator.

After a car hits the door

It happens in every shop sooner or later. A bumped door may come off track, bend a section or knock the opener rail loose. A door hit hard should not be run again until it has been looked at, because a twisted section can bind and pull the cables off the drums. Our page on a garage door hit by a car covers what usually needs repair.

Keeping bays working

Shops that have their doors serviced on a regular plan see fewer surprise breakdowns. A visit covers springs, cables, rollers, hinges, the operator and the safety devices, so small wear is found before a door stops in the middle of a busy day.

Windows and visibility

Mechanics like to see who is pulling up, and customers like to see their car inside. A row of windows in the bay doors does both, and it brings daylight into the bays so the lights do not have to carry the whole load. On rolling steel doors, vision slots in the curtain give a little of the same benefit. Windows on a shop door should be tough, since a stray tool or a ladder can knock into them, so we often suggest polycarbonate in place of glass on the lower rows.

Brands we work on

We repair and adjust doors and operators from the major commercial brands used in shops across our area, and we can replace a worn door with one better suited to how the shop works.

What a visit includes

The technician checks each bay door and its operator, notes what is worn, and explains what needs work now and what can wait. You get a free estimate before any work starts.

Questions we get asked

What is the best garage door for an auto repair shop?

An insulated sectional door with windows, or a rolling steel door where ceiling space is needed for lifts.

Why do shop door springs break so often?

Springs wear by cycles. Shop doors open far more often than home doors, so they need springs rated for heavy use.

Can a door be set up so it does not hit a car lift?

Yes. Tracks can run higher on the wall, or a rolling door can be used to keep the ceiling clear.

Should we run a door after a car hits it?

No. Have it checked first. A twisted section can bind and pull cables off the drums.

Is the estimate free?

Yes. We check the doors before any work starts.

Booking takes a minute

Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.

Free estimate, call (929) 429-2429.

Bay door giving you trouble? Tell us about the shop

Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.

Easier to explain by phone? Call (929) 429-2429.

Two minutes to a free estimate

Tell us what the door is doing. The estimate is free either way.

Or just call (929) 429-2429 and talk it through.

The other six things that go wrong