
Takes 30 seconds. We call you back to set a time.
You hit the remote, the opener motor starts, the light comes on, and the door does not budge. Or the chain or belt moves along the rail while the door stays where it is. This is one of the most common opener calls we get, and the good news is that the motor itself is often fine. Something between the motor and the door has let go, or the door has become too heavy for the opener to move. Free estimate at (929) 429-2429.
By Sean Cohen, owner, On Point Garage Doors · Updated
These photos are from our own jobs, with our logo on them.



An opener is a motor that turns a gear, the gear drives a chain, belt or screw, and that pulls a trolley along the rail. The trolley is hooked to an arm bolted to the top of the door. When any link in that line breaks or comes apart, the motor can run happily while the door never feels it.
The other possibility is the door itself. Springs carry almost all of the door's weight. When a spring breaks, the door becomes far heavier than the opener was built to lift, and the opener strains, stops or reverses.
It helps to tell us what you see and hear. Does the chain or belt move along the rail? Does the motor hum without anything moving? Did you hear a loud bang in the garage recently? Is there a gap in the spring above the door?
Those answers usually point us to the cause before we arrive, so the right parts are on the truck. Please do not try to force the door up with the opener or by pulling on it, and stay clear of the springs.
A garage door can weigh as much as a small motorcycle. Springs balance that weight so the opener only has to guide the door. When a spring snaps, the opener is suddenly asked to lift the full weight. Most openers sense the strain and stop, which makes it look like the opener died.
Running the opener against a door with a broken spring can strip its gear or bend the door's top section, so it is worth stopping and calling as soon as you suspect a spring.
On many chain and belt openers, the motor drives a plastic worm gear. After years of use, or after the opener has fought a heavy door, the teeth wear away. The motor runs, you may hear a grinding or whirring sound, and the trolley never moves.
If the rest of the opener is in good shape, a new gear set brings it back. If the opener is old, has no modern safety sensors or has other worn parts, we give you a free estimate on a new opener as well, so you can choose.
A chain that has gone slack can jump off its sprocket. A rubber belt can crack and snap. A screw drive can wear its carriage. Each of these leaves the motor turning while the door stays put.
We set the drive back on, replace what is worn, and adjust the tension so the drive runs smoothly without slapping the rail.
A door with a bent track, a broken roller, a frayed cable or a twisted bottom section can bind so hard that the opener cannot push it. The opener protects itself by stopping or reversing.
Fixing the opener alone would not help, so we always look at the whole door: springs, cables, rollers, hinges and tracks, and the balance of the door with the opener disconnected.
The technician checks the opener, the drive and the trolley, then disconnects the door and tests its weight and balance. That tells us quickly whether the problem is in the opener or in the door.
You get a clear explanation and a free estimate before any work starts. Once it is fixed, the door is run several times, the force and travel settings are set, and the safety reverse is tested.
A door stuck open leaves the garage, and often the house, exposed. If that is your situation, tell us when you call. The technician secures the door first and fixes the cause second, so you are not left with an open garage overnight.
A yearly tune-up catches a tired spring, a worn gear or a slack chain before they leave you stuck. Listening for new sounds also helps: grinding from the opener, or a door that seems to work harder than it used to, are early warnings worth a visit.
Most often the trolley is disconnected, the drive gear is stripped, the chain or belt is broken, or a spring has broken and the door is too heavy for the opener.
Yes. Springs carry the weight of the door. Without them the opener cannot lift it and usually stops or reverses.
No. Running the opener against a heavy or stuck door can strip its gears or bend the door. Stop and call.
Not always. A new gear, belt or chain often fixes it. If the opener is old or worn in several places, we give you a free estimate on a new one too.
Yes. The technician finds the cause and explains your options before any work starts.
Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.
Free estimate, call (929) 429-2429.
Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.
Easier to explain by phone? Call (929) 429-2429.
Tell us what the door is doing. The estimate is free either way.