Serving Brooklyn, Queens and Long Island(929) 429-2429Open six days a weekFree estimateGuaranteed work
On Point Garage Doors
Open 24 hours Sun-Thu, Fri until 5 pm Free estimate Springs, openers, cables We come to you
Emergency?Call nowBook free estimate
New York, NY - open six days a week

Commercial garage door spring replacement

Free estimateSame-day serviceCommon parts on board
  • Free estimate
  • Same-day service
  • Common parts on board
Emergency garage door repair★★★★★ 5.0 on Google · 42 reviews

Book your free estimate

Takes 30 seconds. We call you back to set a time.

Or just call (929) 429-2429 and talk it through.

Home › Commercial Spring Replacement

On a commercial door the springs do almost all of the lifting. A dock door, a shop bay door or a rolling steel door can weigh many times what a home door weighs, and the springs carry that weight every time the door opens. When one breaks, the door either will not move or the operator strains to lift it, and a business that depends on the door is stuck. Commercial springs are larger, more tightly wound and more dangerous than residential springs, and they are matched to each door by weight, size and how many times it opens. This page explains how those springs work, why they fail and what a replacement visit involves. Free estimate at (929) 429-2429.

By Sean Cohen, owner, On Point Garage Doors · Updated

Real jobs. Real photos.

These photos are from our own jobs, with our logo on them.

Broken spring with a gap in the coils, from one of our jobs
Broken spring with a gap in the coils
Spring, cable and drum up close, from one of our jobs
Spring, cable and drum up close
Roll-up door at a loading dock, from one of our jobs
Roll-up door at a loading dock

What the springs do on a commercial door

Springs balance the weight of the door so the operator, or a person pulling a chain, only has to move a small part of it. On a sectional door the torsion springs sit on a shaft above the opening and wind cables onto drums. On a rolling steel door the spring is hidden inside the barrel that the curtain coils around. Either way, when the spring is right the door feels light, and when it is weak or broken the full weight lands on the operator or the hoist.

Signs a spring is failing

Why commercial springs break

Every spring is made for a certain number of cycles. A door that opens many times a day uses up that life quickly, and the spring eventually cracks at a point of stress. Rust shortens the life further, which is why doors near the water and doors in wet or salted bays break springs sooner. Doors that are out of balance, doors with worn bearings and doors that are hit by trucks also put extra load on the springs.

High-cycle springs

A high-cycle spring is made from heavier wire and wound longer, so each turn carries less stress and the spring lasts far longer on a busy door. It takes more room on the shaft and it needs to be calculated for the door, but on a dock door or a service bay that opens all day, it is usually the better choice. We look at how often the door runs before recommending the standard or the high-cycle option.

Rolling steel door springs

On a rolling door the spring sits inside the barrel, so it cannot be seen from the floor. When it weakens, the door feels heavy and the operator works harder. When it breaks, the door may refuse to move or may come down hard. Replacing it means taking the tension off safely, removing the barrel or opening it up, and setting the new spring with the right number of turns for the curtain.

Why this is never a job for staff

A commercial spring holds a great deal of stored energy. Taking a broken spring off and putting a new one on calls for the right winding tools, a secure way to hold the door and training in how the tension is released and set. Staff should never try to adjust or replace a commercial spring, and a door with a broken spring should be kept closed and blocked off until the technician arrives.

Matching the spring to the door

The new spring is matched to the door as it is now, not to the label on the old one. Doors gain weight over the years when struts, windows, insulation or heavier hardware are added. The technician measures the door, works out its weight and calculates the wire, the length and the inside size of the spring, so the door ends up balanced with the operator unhooked.

Cables, drums and bearings

A spring that broke has often been working against worn cables or tired bearings. On a commercial door we look at the cables for fraying and rust at the bottom brackets, the drums for wear, and the bearings at each end of the shaft. Replacing a frayed cable at the same time as the spring saves a second visit and a second shutdown.

Doors with two springs or more

Many commercial doors carry two, four or more springs on one shaft. When one breaks, the others are the same age and have done the same work. Replacing the full set keeps the door balanced and avoids another break a short while later. We explain what we see on the other springs and let you decide.

Getting the business back open

A broken spring on the only door into a warehouse or a shop is an urgent call. The technician carries the common sizes and can often finish the job on the first visit. Large or unusual springs may need to be ordered, and if so the door is made secure and the business is told plainly what happens next.

What a visit includes

The technician makes the door safe, measures it, explains what has broken and what else is worn, and gives a written estimate. Once you approve it, the old springs come off, the new ones go on, the cables and drums are set, and the door is balanced and tested with the operator. The old springs leave with the technician.

Questions we get asked

How do I know if a commercial door spring is broken?

A loud bang, a door that will not lift, a gap in the coils, or an operator that strains and stops are the usual signs. Keep the door closed and call before anyone tries to force it.

Are high-cycle springs worth it on a dock door?

On a door that opens many times a day, usually yes. They are made to last far longer under heavy use, which means fewer breakdowns and fewer shutdowns.

Can you replace the spring on a rolling steel door?

Yes. The spring sits inside the barrel, so the tension is released safely, the spring is replaced and the barrel is set with the right number of turns for the curtain.

Should all the springs be replaced if only one broke?

Usually it is best, because the others are the same age and have done the same work. We show you their condition and let you decide.

Is the estimate free?

Yes. The technician looks at the door and the springs and gives you a written estimate before any work starts.

Booking takes a minute

Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.

Free estimate, call (929) 429-2429.

Spring broke on a commercial door? We will get it lifting

Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.

Easier to explain by phone? Call (929) 429-2429.

Two minutes to a free estimate

Tell us what the door is doing. The estimate is free either way.

Or just call (929) 429-2429 and talk it through.

The other six things that go wrong