Serving Brooklyn, Queens and Long Island(929) 429-2429Open six days a weekFree estimateGuaranteed work
On Point Garage Doors
Open 24 hours Sun-Thu, Fri until 5 pm Free estimate Springs, openers, cables We come to you
Emergency?Call nowBook free estimate
New York, NY - open six days a week

Wayne Dalton TorqueMaster spring repair

Free estimateSame-day serviceCommon parts on board
  • Free estimate
  • Same-day service
  • Common parts on board
Emergency garage door repair★★★★★ 5.0 on Google · 42 reviews

Book your free estimate

Takes 30 seconds. We call you back to set a time.

Or just call (929) 429-2429 and talk it through.

Home › TorqueMaster Spring Repair

Many Wayne Dalton doors use a spring system called TorqueMaster. Instead of an open spring on a bar above the door, the springs are hidden inside a steel tube that runs across the top of the opening, with winding hardware at the ends. It looks tidy, but it works differently from standard torsion springs, and repairing it needs a technician who knows the system. Free estimate at (929) 429-2429.

By Sean Cohen, owner, On Point Garage Doors · Updated

Real jobs. Real photos.

These photos are from our own jobs, with our logo on them.

New garage door spring installed by On Point Garage Doors
Springs and cables
Cable drum at the end of the bar, from one of our jobs
Cable drum at the end of the bar
Broken garage door spring with a gap in the coil, before On Point Garage Doors replaced it
Standard torsion spring cone

How TorqueMaster is different

On a standard system, the springs are out in the open on a bar, and you can often see a gap when one breaks. On TorqueMaster, the springs sit inside the tube, so you cannot see a break. The door simply becomes very heavy, lifts unevenly or will not open with the opener.

The system also has its own drums, cables and winding parts, and some versions have a counter at the end that shows how the springs are set. Parts are specific to the system.

Signs a TorqueMaster spring broke

  1. The door will not liftThe opener hums, strains or lifts the door a little and stops.
  2. A loud bangOften heard from the garage, even though you cannot see anything broken.
  3. Slack cablesWith the spring gone, the cables can go slack and come off their drums.
  4. Door uneven or heavyOne side lags or the door drops when stopped partway.

Replace the TorqueMaster or convert

There are two good options. We can replace the springs inside the TorqueMaster tube with the correct parts for your door. Or we can convert the door to a standard torsion spring system with open springs, new drums, bearings and cables.

Conversion is often the better long-term choice: standard torsion springs are easy to service, easy to size for longer life, and parts are available everywhere. The technician explains both options with a free estimate, and you choose.

Why springs fail in the first place

Springs wear out with use, no matter the system. A door that opens many times a day wears its springs much sooner. Cold winters make tired steel more likely to snap, and damp garages add rust. On older TorqueMaster doors, the springs are often original and well past their working life.

Please leave the tube alone

The springs inside the tube hold enough force to lift the whole door. The winding parts at the ends are under tension even when the door is closed. Please do not try to wind, open or remove any part of the system, and do not keep running the opener against a heavy door. Keep clear and call.

Cables and drums

When a TorqueMaster spring breaks, the cables often jump off their drums or tangle. Those cables are checked and replaced when worn, and the drums are inspected. If we convert the door, new drums and cables come with the new springs.

Wayne Dalton doors we service

Wayne Dalton doors are common in homes across Long Island, Queens and Brooklyn, from basic steel doors to insulated and carriage models. Many of them have TorqueMaster springs, and many others have standard torsion springs. We service both, along with Wayne Dalton panels, rollers, hinges and seals. Everything on the door besides the spring is covered under Wayne Dalton repair.

The opener after a spring repair

Once the new springs are in, the door is balanced and the opener's force and travel are set again. An opener that strained against a broken spring may have worn its gear, so it is tested too. Some Wayne Dalton doors were paired with their own openers; those are checked and, when worn out, a new opener is explained with a free estimate.

What the visit includes

The technician confirms the spring system on your door, checks the cables, drums and bearings, explains the repair and conversion options with a free estimate, and does the work you choose. Before leaving, the door is balanced, run several times and the safety reverse is tested.

TorqueMaster on older and newer doors

Wayne Dalton has used more than one version of the TorqueMaster system over the years, and the parts are not all the same. Identifying which version is on your door matters before anything is ordered. The technician checks the labels, the end brackets and the tube to confirm it.

On some doors the system was paired with a Wayne Dalton opener made to work with it. When the door is converted to standard springs, the opener is checked to make sure it still suits the door.

Is it worth fixing the door

Most Wayne Dalton doors with a broken TorqueMaster spring are well worth repairing. If the door also has cracked sections, rust through the bottom or is very old, we give you a free estimate on a new door as well, so you can compare.

Questions we get asked

What is a TorqueMaster spring?

A Wayne Dalton spring system where the springs sit inside a steel tube above the door instead of on an open bar.

How do I know my TorqueMaster spring is broken?

You usually cannot see it. The door becomes very heavy, lifts unevenly or will not open with the opener, often after a loud bang.

Can TorqueMaster be converted to standard springs?

Yes. Converting to a standard torsion system is often the better long-term choice, and we explain both options.

Can I adjust a TorqueMaster spring myself?

No. The system is under high tension and needs a trained technician with the right tools.

Is the estimate free?

Yes. You see the repair and conversion options before any work starts.

Booking takes a minute

Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.

Free estimate, call (929) 429-2429.

Not sure what is wrong? We will come and look

Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.

Easier to explain by phone? Call (929) 429-2429.

Two minutes to a free estimate

Tell us what the door is doing. The estimate is free either way.

Or just call (929) 429-2429 and talk it through.

The other six things that go wrong