Serving Brooklyn, Queens and Long Island(929) 429-2429Open six days a weekFree estimateGuaranteed work
On Point Garage Doors
Open 24 hours Sun-Thu, Fri until 5 pm Free estimate Springs, openers, cables We come to you
Emergency?Call nowBook free estimate
New York, NY - open six days a week

Genie garage door opener not working

Free estimateSame-day serviceCommon parts on board
  • Free estimate
  • Same-day service
  • Common parts on board
Emergency garage door repair★★★★★ 5.0 on Google · 42 reviews

Book your free estimate

Takes 30 seconds. We call you back to set a time.

Or just call (929) 429-2429 and talk it through.

Home › Genie Opener Not Working

Genie openers are on a great many garages in Brooklyn, Queens and Long Island, from old screw-drive units that have run for years to newer belt-drive models with phone control. When a Genie stops working, the cause is usually one of a few familiar problems. We repair Genie openers every week, and most of the time the opener can be brought back without replacing the whole unit. Free estimate at (929) 429-2429.

By Sean Cohen, owner, On Point Garage Doors · Updated

Real jobs. Real photos.

These photos are from our own jobs, with our logo on them.

Opener on the ceiling, from one of our jobs
Opener on the ceiling
Safety sensor on the track, from one of our jobs
Safety sensor on the track
Opener circuit board, from one of our jobs
Opener circuit board

What your Genie is doing

  1. Door will not close, light flashesUsually the safety sensors: blocked, dirty, out of line or with a damaged wire.
  2. Motor runs, door does not moveA worn gear, a worn screw-drive carriage or a disconnected trolley.
  3. Door reverses or stops partwaySensors, travel limits, force settings or a door that binds.
  4. Remote does nothing, wall button worksRemote battery, lost pairing, lock mode or a weak receiver.
  5. Nothing at allPower, the outlet, the wall control wiring or the circuit board.

Genie safety sensors

Genie sensors sit low on each side of the door, and each has a small light. When they are lined up and clear, the lights show steady. When one blinks or is off, the beam is broken or a sensor has failed, and the opener will not close the door, or reverses it.

Sensors get knocked by bikes, bins and feet, and their wires get pinched along the wall. We set them solidly, protect the wiring and replace sensors that have failed.

Screw-drive Genies

Many older Genies use a long threaded rod instead of a chain or belt. They are simple and strong, but the carriage that rides on the screw wears over time, and the rod needs the right grease to run smoothly. A worn carriage makes a grinding or chattering sound and can let the door slip.

Replacing the carriage often brings a screw drive back to life. If the rest of the unit is worn too, a new opener is explained with a free estimate.

Belt and chain Genies

On belt and chain models, the drive gear and the sprocket are the parts that wear most. A slack chain slaps the rail and can jump off its sprocket; a belt can crack with age. Gears wear faster when the opener has been lifting a door with tired springs.

Lights and codes

Many Genie openers flash their light or a small LED in patterns to show what is wrong: sensor problems, a force or limit issue, or a fault in the opener. If you tell us what the lights are doing, we can often narrow down the cause before the visit.

Remotes and keypads

Genie remotes and keypads work with Genie openers, and they need to be paired. After a power surge, a new board or a new remote, pairing may need to be done again. A lost or stolen remote should be cleared out of the opener's memory. We pair and test every remote, keypad and car button during the visit.

Aladdin Connect

Genie's phone app, Aladdin Connect, lets you open and close the door from anywhere and get alerts. When it stops working, the cause is usually the Wi-Fi signal in the garage, a changed router or password, or the small sensor on the door that reports its position. We reconnect it and test it from your phone.

Check the door before the opener

Many Genie problems are really door problems. A broken spring makes the door too heavy, and the opener strains, stops or reverses. Worn rollers and a bent track make the door bind. Before any opener part is replaced, the door is disconnected and its balance is tested by hand.

Fixing it or a new Genie

Gears, carriages, sensors, wall controls, remotes and many boards can be replaced. On very old units, some parts are no longer made, and a new opener with rolling-code remotes, safety sensors and phone control is the better choice. You get a free estimate on both so you can compare.

What a visit includes

The technician identifies your Genie model, tests the door's springs and balance, checks the sensors, the drive, the board, the remotes and the wall control, and explains what is wrong with a free estimate. After the repair, the travel and force are set, and the safety reverse is tested with an object in the opening.

Genie and the other brands

We work on Genie, LiftMaster, Chamberlain, Craftsman, Linear, Marantec and older brands, and we install them too. If you are thinking about replacing an old Genie, we can show you new Genie models side by side with other brands and explain which fits your garage best.

Questions we get asked

Why will my Genie opener not close the door?

Usually the safety sensors are blocked, dirty, out of line or wired badly. Travel limits or a binding door can also cause it.

Why does my Genie hum but not move the door?

Often a worn drive gear or screw-drive carriage, a disconnected trolley, or a broken spring making the door too heavy.

Can a Genie screw-drive opener be repaired?

Yes. A worn carriage is a common fix. If the whole unit is worn out, a new opener is often better.

Why is Aladdin Connect not working?

Usually weak Wi-Fi in the garage, a changed router or password, or a door sensor with a weak battery.

Is the estimate free?

Yes. You see what is wrong and the options before any work starts.

Booking takes a minute

Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.

Free estimate, call (929) 429-2429.

Not sure what is wrong? We will come and look

Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.

Easier to explain by phone? Call (929) 429-2429.

Two minutes to a free estimate

Tell us what the door is doing. The estimate is free either way.

Or just call (929) 429-2429 and talk it through.

The other six things that go wrong