
Takes 30 seconds. We call you back to set a time.
Genie is one of the brands we install most often, partly because so many garages in our area already have one and partly because the screw-drive models suit a lot of the older, simpler doors we see. A good Genie install is more than hanging a motor from the ceiling. The door has to be balanced, the rail has to line up with the center of the door, the sensors have to see each other, and the remotes and the app have to work on the first try. We install Genie openers across Brooklyn, Queens and Long Island, including units you picked up at a store and want put in properly. Free estimate at (929) 429-2429.
By Sean Cohen, owner, On Point Garage Doors · Updated
These photos are from our own jobs, with our logo on them.



Genie is known for screw-drive openers, where a long threaded rod turns and moves the trolley. They have few moving parts and suit garages that stay fairly mild. Belt-drive Genies are the choice when there is a bedroom or a home office over the garage, because they run much more quietly. Chain-drive Genies are simple and strong and are common in detached garages where noise does not matter. We talk through which one fits your garage before anything is ordered.
A light single steel door and a heavy insulated two-car door do not need the same opener. We look at the size and weight of the door, whether it has windows or a wood overlay, and how often it is used. A heavier door or a busy household is a reason to choose a stronger unit. An opener that is too small for the door will strain, wear its gear early and stop on cold mornings.
Before we hang a new Genie we disconnect the old opener and lift the door by itself. If it is heavy, drifts down or flies up, the springs are out of balance, and no opener will make up for that for long. We also look at the rollers, the hinges and the tracks. Fixing the door first is what lets a new opener run quietly for years instead of fighting the door from the first day.
The rail has to be centered on the door and fixed solidly at the header above the opening. The motor hangs from the ceiling joists on proper hangers, not from drywall alone. In many older garages the joists run the wrong way or the ceiling is finished, so we add a solid backing to mount to. The arm is attached to the top section of the door with a bracket, and on wide or light doors we add a strut so the top section does not bend.
Genie calls its safety sensors Safe-T-Beam. They mount low on each side of the opening and the door will not close if the beam is blocked. We run the wires neatly along the wall and track, line the sensors up so the indicator lights stay steady, and keep them out of the way of bikes and bins. The wall console goes by the house door, high enough that small children cannot reach it.
Genie openers use rolling-code remotes, so the code changes every time and cannot simply be copied. We pair every remote you have, set up an outdoor keypad if you want one, and pair the button built into your car if it is compatible. Older Genie remotes from a previous opener do not always work with a new unit, so we check each one and tell you which to keep.
Many current Genie models have Aladdin Connect built in, and older ones can take an add-on. It lets you open, close and check the door from a phone. A garage is a hard place for Wi-Fi, with metal doors, block walls and long distances to the router. We check the signal where the opener hangs before we promise the app will be reliable, and we set it up with you so the app is working when we leave.
Some garages have little room above the door, a beam in the way or a ceiling that slopes. A standard rail may not fit, or the door may need a different track setup. We measure the space at the estimate and tell you plainly whether a Genie on the ceiling will work, or whether a wall-mounted opener from another maker suits your garage better.
If there is an old opener on the ceiling, we take it down, remove the old rail, sensors and wiring, and leave the garage clean. Old brackets on the door that are no longer used get removed or covered. If the old opener had a light or a battery backup you relied on, we make sure the new Genie covers the same need.
Plenty of people pick up a Genie at a store and then find the box has more parts than they expected. We install openers you bought, as long as the unit suits the door. If the model is too small for the door or will not fit the garage, we tell you before we start so you can return it. We bring the hardware that store kits usually leave out, like solid hangers and backing.
Yes, as long as the model suits the door and the garage. If it does not, we tell you before we start.
Screw drives are louder than belt drives but have few moving parts. If there is a room over the garage, we usually suggest a belt-drive Genie.
Sometimes. It depends on the remote and the new unit. We test each one and pair the ones that work.
Yes. We check the Wi-Fi signal in the garage first, then set up the app with you before we leave.
Yes. We look at the door, the ceiling and your controls, and give you a written estimate before any work starts.
Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.
Free estimate, call (929) 429-2429.
Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.
Easier to explain by phone? Call (929) 429-2429.
Tell us what the door is doing. The estimate is free either way.