
Takes 30 seconds. We call you back to set a time.
The wall button is the control by the door into the house or beside the garage door. It is the one control in the garage that should always work, even when a remote battery is dead. When pressing it does nothing, or it works only some of the time, the cause is usually simple, but finding it means checking the button, the thin wire running to the opener and the opener itself. Whether the remotes still work tells us a lot about where the problem is. Free estimate at (929) 429-2429.
By Sean Cohen, owner, On Point Garage Doors · Updated
These photos are from our own jobs, with our logo on them.



If the remotes work but the wall button does not, the opener has power and its board is working, so the trouble is in the button or its wire. If nothing works, not the remotes and not the button, the problem is more likely the opener, its power or its safety sensors.
Many wall controls have a lock or vacation button. When it is on, the remotes stop working and the opener ignores most signals, which often leads owners to think the button is broken too. A small light on the control usually blinks to show lock mode. Turning it off restores normal use.
Older openers use a plain doorbell-style button that closes a circuit. Newer openers use a smart wall control with a light, a lock button and sometimes a screen, which talks to the opener in a coded way. A smart control from one brand or one series will not work on another, so a replacement must match the opener.
A button that works on the third or fourth press usually has worn contacts inside or a wire that is barely touching. Cold weather can make it worse. Smart controls can also act up when the wire is damaged in a way that still lets some signal through.
If the door opens from the button but will not close, and the opener light blinks, the safety sensors at the bottom of the tracks are often blocked or out of line. On many openers, holding the wall button down will close the door, which is a clue that the sensors are the problem. Our page on garage door sensors explains this.
If neither the button nor the remotes work, the opener may have lost power, tripped a breaker, or have a failed board or motor. A burned board, often after a storm or power surge, can leave the opener dead even though the outlet still has power.
In two-family homes and shared garages, a second wall button is often added at another entry. Each extra button and longer wire run adds places for a fault. A wireless wall button or a keypad can be simpler where running wire is hard.
The wall button is the control you reach for when a remote is lost, a battery dies or a child needs to close the door from inside. It also lets the door be closed by holding the button when a sensor is out of line. It is worth keeping in working order.
Even with a working wall button, many owners like a second way in. A keypad mounted outside the garage door lets family members open it without a remote, and a smart opener lets you check from your phone whether the door is open and close it from anywhere. These do not replace the wall button, but they mean a failed button never leaves you locked out of the garage. We set up keypads and phone control on most current openers and test them with every remote in the house.
Many smart wall controls also switch the opener light and show a small light of their own. If the control is dark while the opener still has power, the wire or the control has likely failed. A lit control that does nothing points more to the opener board.
If the button itself has failed, the technician fits a control matched to your opener and tests it with the remotes, the keypad and the sensors. If the opener is old and the matching controls are no longer made, they will explain whether a new opener is the better step.
The technician checks the button, the wire and the opener, finds the fault and explains the repair. You get a free estimate before any work starts.
Usually the button or the thin wire to the opener has failed. A staple or a mouse can damage the wire.
The opener may have lost power or have a failed board, or lock mode may be on.
A setting that stops the remotes from working. A blinking light on the control often shows it is on.
No. Smart wall controls must match the opener brand and series.
Yes. We check the button, the wiring and the opener before any work starts.
Across Brooklyn, Queens and Long Island, tell us what the door is doing and we set a visit that fits your day.
Free estimate, call (929) 429-2429.
Tell us what the door is doing and we will give you an honest arrival time. The estimate is free.
Easier to explain by phone? Call (929) 429-2429.
Tell us what the door is doing. The estimate is free either way.